Make It Yourself

 
Emerald and Fig’s Greeting from Richmond Hoop Art. Image of hoop with hand holding a pink and white dogwood (Virginia’s state flower).
 

INSTRUCTIONS

Place the fabric: Trim your fabric so that it will fit nicely in the hoop with a few inches to spare all the way around. (This excess will be used when you finish the back of the hoop.) Loosen the screw at the top of the embroidery hoop and separate the outer hoop from the inner hoop. Lay the inner hoop on a flat surface, center your fabric on top of it, then place the outer hoop on top so that the fabric is in between the inner and outer hoops. Tighten the screw and pull the fabric taut.

Transfer the pattern: Visit bsidecollective.com to download a copy of the pattern. Print the pattern, cut it out so that it fits inside the hoop, and then tape it to the backside of the fabric. Next, trace the pattern onto the fabric using your transfer pen.

Thread the needle: Choose the floss that you want to start with and cut off a piece about 12 to 18 inches long. You want the floss to be long enough to work with, but if it’s too long, it can end up in knots. You can use a needle-threader to thread the needle, but it’s not necessary. Make sure you have a few inches hanging through the eye of the needle so that the floss doesn’t slip out as you’re stitching. A standard thread of embroidery floss has six individual strands. Some of the stitches in this design use all six strands, but some require you to split the strands for a finer looking stitch.

Stitch: This design uses backstitch, whipped backstitch, satin stitch, long and short stitch, and French knots. If you’re not familiar with these stitches, I recommend searching YouTube for the name of the stitch. There are many wonderful tutorials available online.

  • “Greetings from” – backstitch with three strands of DMC 931

  • Hand outline – backstitch with one strand of DMC 310

  • Branch – backstitch with six strands of DMC 840

  • Flower petals – Long and short stitches with three strands each of DMC 352, 818, and Ecru. For a simpler alternative, you could use satin stitch in a single color for the petals.

  • Flower centers – French knots using six strands of DMC 3819

  • Leaves – Satin stitch using six strands of DMC 470

  • “Richmond” – Whipped backstitch in DMC 931, using six strands for the backstitch and three strands for the whipping. You could also forgo the whipping and just use backstitch.

Rinse: This step is only necessary if you used a water-soluble pen to transfer the pattern. Remove the fabric from the hoop and run it under warm water until your pen marks disappear. Gently squeeze out the excess water and hang to dry.

Finish your hoop: First, make sure that your design is centered in the hoop and that the fabric is nice and tight. Next, trim away any excess fabric, leaving about half an inch of fabric outside the hoop. Sparingly apply glue all the way around the edge of the extra fabric, making sure that you’re keeping the glue close to the hoop. Press the fabric onto the inner edge of the hoop, making sure that it’s tight as you go all the way around the hoop.

You can tag your photos on Instagram with @emeraldandfigdesigns.



Emmie McMackin of Emerald & Fig Designs

Emmie McMackin of Emerald & Fig Designs

Visit emeraldandfig.etsy.com to purchase a complete kit for this design that includes pre-printed fabric, floss, needle, and hoop.

SUPPLIES

  • Six-inch embroidery hoop

  • Fabric (Kona cotton is my favorite)

  • DMC embroidery floss in the following colors: 310 Black, 352 Pale Coral, 470 Light Avocado Green, 818 Baby Pink, 840 Medium Beige Brown, 931 Medium Antique Blue, 3819 Light Moss Green, and Ecru.

  • Size 5 embroidery needle

  • Water-soluble transfer pen

  • Scissors

  • Optional items: Needle threader, glue for finishing your hoop